Skip to content

Outsource CE documentation or do it yourself with software?

Hiring a service provider for CE documentation pays off mainly for a first project without in-house experience, for machinery where a notified body has to be involved and when internal capacity is lacking; for recurring machines, variants and product lines, doing it yourself with software usually works out cheaper, because templates and know-how stay in-house. Responsibility remains with the manufacturer in every case, and the declaration of conformity is always issued and signed by the manufacturer, not by the service provider.

Risk assessment, operating instructions, technical file or declaration of conformity: this guide shows when each route fits, what the routes cost and how long they take, and per document what you can hand over and what stays with you. It applies equally if you manufacture outside the EU and supply machinery into the EU.

Service provider, software or both: when each route fits

A service provider makes sense if …

  • you are CE marking your first machine and nobody in-house has experience with risk assessment, standards and technical documentation yet. The assignment pays off most if your team works alongside and learns the method.
  • a notified body has to be involved for the machine, for example for certain machinery under Annex IV of the Machinery Directive or Annex I of the Machinery Regulation. It then pays to agree the scope of the examination and the documents early with experienced support.
  • you lack internal capacity because the delivery date is fixed and the design team is fully booked.
  • a borderline case needs to be resolved, such as a substantial modification, an assembly of machinery or the validation of safety-related control systems.

Doing it yourself with software is enough if …

  • you know your machine and someone in-house is responsible for the CE documents, even without a CE department of your own.
  • you build recurring machines, variants or product lines: projects from templates and building blocks carry hazards, standards and safety functions over into the next variant, with hazards taken over marked “to be reviewed”.
  • after placing on the market you need to keep track of changes to standards, modifications and series production, and the documents must stay up to date for years.

Combine both if …

  • you work in the software yourself and have the first project, individual documents or borderline cases reviewed by a service provider, for example on the basis of the Word export.
  • a service provider should work directly in your projects: on the Business plan you invite them as one of the 5 user profiles, with the role editor or read-only, and the audit trail shows who changed what. The invitation goes to an email address that does not already belong to another account.
  • a service provider prepares the first project and you derive the variants from it yourself.

Whether your machine needs a notified body is covered in the guide Annex IV machinery.

Cost, time and responsibility compared

The cost ranges are industry figures as of 2026. They come from the guide on CE marking costs, which also breaks down internal costs, prices of standards and the cost of a notified body.

Comparison: CE documentation by a service provider, yourself with software, or both
CriterionService providerSoftware, yourselfBoth
Direct costsComplete outsourcing roughly €3,000 to €15,000 per simple machine, €15,000 to €50,000 and more for complex plants and linked systems; day rates roughly €600 to €2,000Software, for example CE-Copilot from €99 per month on the annual plan (Starter, final price), plus buying standardsSoftware plus day rates for targeted reviews, for example of the first project or of borderline cases
TimeAccording to service providers often a few weeks to several months from data collection, depending on complexityDepends on your capacity, can be planned in parallel with the designOwn preparation in step with the design, review dates with the service provider planned ahead
Your own effortLower, but never zero: machine data, drawings, circuit diagrams, coordination and approvalsRemains the largest item; guided workflows, templates and AI suggestions shorten research and writingAs with the software, plus coordinating the reviews
Know-how stays in-houseMostly with the service providerYes, in projects, templates and building blocksYes, complemented by the service provider's experience
ResponsibilityWith the manufacturer; it cannot be handed overWith the manufacturerWith the manufacturer
Follow-up projects and product linesNew assignment, the costs largely arise againProjects from templates and building blocks; hazards taken over are marked “to be reviewed”Have the first project reviewed, derive variants yourself from the template

Responsibility for conformity stays with the manufacturer in all three cases. A service provider is liable for its own work under its contract, but it does not become the manufacturer of the machine. If you are based outside the EU, you also need an economic operator established in the EU, such as an importer or an authorised representative (Article 4 of Regulation (EU) 2019/1020); a documentation service provider only takes on that role if you appoint it as your authorised representative by written mandate. More in Exporting machinery to the EU without an EU entity.

What you can hand over per document, and what stays with you

Risk assessment

You can hand over: Moderating the hazard analysis, the method per EN ISO 12100, documentation and proposals for protective measures.

What stays with you: Under the general principles in Annex I of the Machinery Directive and Annex III of the Machinery Regulation, the manufacturer ensures that a risk assessment is carried out. Knowledge of the design, use and limits of the machine comes from your company, and you decide on the protective measures and the residual risk.

In CE-Copilot: Risk assessment per EN ISO 12100 with hazards across all life cycle phases, risk score before and after the measures, three-step method and AI suggestions that you review before applying them; from Starter.

More: Risk assessment software.

Operating instructions

You can hand over: Editing, structure per Annex I section 1.7.4 of the Machinery Directive or Annex III section 1.7.4 of the Machinery Regulation, layout and translations.

What stays with you: Technical data, operating and maintenance procedures, the residual risks from the risk assessment and the approval. The instructions must match your risk assessment.

In CE-Copilot: Add-on module from Professional, one-time purchase per project (€12.99): chapters per section 1.7.4, pre-filled from the project data, residual risks and applied standards from the risk assessment, export as PDF and Word.

More: Operating instructions software.

Technical file

You can hand over: Compiling and structuring the documents per Annex VII of the Machinery Directive or Annex IV of the Machinery Regulation, and a gap check before approval.

What stays with you: Drawings, circuit diagrams, calculations, test reports and evidence from design and production. Keeping the file for at least ten years and presenting it at the request of the authorities remain obligations of the manufacturer.

In CE-Copilot: Technical file checklist with file upload per item, complete dossier as PDF and Word, and the documents with all attachments as a ZIP archive with checksums; from Starter.

More: Technical documentation software.

Declaration of conformity

You can hand over: A draft with the mandatory content per Annex II of the Machinery Directive or Annex V of the Machinery Regulation, and a check of the standards cited.

What stays with you: Issuing and signing it. The declaration of conformity is a declaration by the manufacturer, by which it takes responsibility for the conformity of the machine; it is signed by a person authorised to sign on behalf of the manufacturer. A service provider can prepare the draft, but cannot sign in your place.

In CE-Copilot: Declaration per Annex II or Annex V with a check of the mandatory content before export, a block when the date does not fit the cut-over of 20 January 2027, and output in six languages; from Starter.

More: Declaration of conformity software.

For CE service providers and engineering consultancies

If you prepare CE documents for clients as a service provider or engineering consultancy, the Business plan gives you up to 5 user profiles in one account and an unlimited number of active projects, one per client and machine with the client's manufacturer details. You hand over the documents as Word and PDF, and from Professional also as a JSON project file that a client with an account of its own on Professional or higher can read in (without operating instructions, requirements list, standards analyses, files and photos). CE-Copilot does not offer your clients access to individual projects.

Prepare it yourself and only have it reviewed where needed

Risk assessment, standards, technical file and declaration of conformity in the same project, free for 14 days with the Starter scope. Licence for three months at a time, paid in advance; monthly subscription at a higher price, no mandatory annual subscription.

FAQ

Frequently asked questions: outsourcing CE documentation

Can I outsource the technical file?
Yes. A service provider can compile and structure the technical file per Annex VII of the Machinery Directive or Annex IV of the Machinery Regulation and check it for gaps. Drawings, circuit diagrams, calculations and test reports still come from your company, and keeping the file for at least ten years and presenting it at the request of the authorities remain obligations of the manufacturer. If you build follow-up machines, keeping the file yourself in software and only having it reviewed is usually cheaper.
How much does it cost to have CE documentation prepared?
For complete outsourcing, service providers quote roughly €3,000 to €15,000 per simple machine and €15,000 to €50,000 and more for complex plants and linked systems; typical day rates for machinery safety consulting are around €600 to €2,000 (industry figures, as of 2026). For follow-up projects these costs largely arise again. For doing it yourself, CE-Copilot costs from €99 per month on the annual plan (Starter, final price); internal effort remains the largest item. Details are in the guide “What does CE marking a machine cost?”.
Can I outsource the risk assessment?
Yes, a service provider can carry it out and document it. The manufacturer must ensure that it is carried out, though, and it needs the manufacturer's knowledge of the design, use and limits of the machine; the decision on protective measures and residual risk stays with the manufacturer. Often the service provider moderates the hazard analysis and your team contributes the knowledge of the machine.
Can I outsource the operating instructions?
Yes. Editing, the structure per Annex I section 1.7.4 of the Machinery Directive or Annex III section 1.7.4 of the Machinery Regulation, layout and translations can be outsourced. You supply the technical data, the residual risks from the risk assessment and the approval, because the instructions must match your risk assessment. In CE-Copilot they are created as an add-on module from Professional from the project data; residual risks and standards come from the risk assessment.
Can a service provider sign the declaration of conformity?
Not in place of the manufacturer. The declaration of conformity is a declaration by the manufacturer, by which it takes responsibility for the conformity of the machine; it is signed by a person authorised to sign on behalf of the manufacturer. A service provider can prepare and check the draft with the mandatory content per Annex II of the Machinery Directive or Annex V of the Machinery Regulation, but the responsibility does not pass to them.

Technical information as of 18 November 2026, not legal advice. Cost ranges are industry figures, not quotes; CE-Copilot prices from the price list as of the same date.

More guides